ASME SA-350 LF2 Long Weld Neck Flanges – LWN Flanges

ASME SA-350 LF2 Long Weld Neck Flanges (LWN Flanges) are forged low-temperature carbon steel flanges with an extended neck or barrel, commonly used for pressure vessels, heat exchangers, vessel nozzles and low-temperature piping connections.

The LF2 material grade provides specified notch toughness for low-temperature service, while the flange face, bolt pattern and pressure class may follow ASME B16.5 where applicable. The extended neck length, bore and hub geometry are normally manufactured to the equipment drawing or project specification.

ASME SA-350 LF2 Long Weld Neck Flanges Specification

Item Specification
Product Long Weld Neck Flange / LWN Flange
Material ASME SA-350 LF2 / astm_a350_lf2
Material Type Low-Temperature Carbon Steel Forging
Classes LF2 Class 1 / Class 2
Flange Standard ASME B16.5 where applicable
Pressure Classes 150 / 300 / 400 / 600 / 900 / 1500 / 2500 as applicable
Facing RF / RTJ / FF where specified
Neck Length Standard or Custom to Drawing
Bore To pipe schedule, vessel neck or customer drawing
Manufacturing Forging + Heat Treatment + Machining
Inspection CVN, UT, MT, dimensional inspection and additional tests as specified

What Is a Long Weld Neck Flange?

A Long Weld Neck Flange, also called an LWN flange, is similar to a conventional welding neck flange but has a significantly extended neck.

The extended neck may be welded directly to:

  • pressure vessel shells;
  • vessel heads;
  • heat exchangers;
  • columns;
  • reactors;
  • piping systems.

LWN flanges are widely used as pressure vessel nozzles because the long forged neck can replace a separate pipe neck and provide a continuous forged connection between the flange and equipment.

SA-350 LF2 Material

ASTM A350 / ASME SA-350 LF2 is a carbon-steel forging grade intended for low-temperature piping components where notch toughness is required.

The current ASTM A350 specification covers forged or ring-rolled flanges, fittings, valves and similar components for low-temperature service.

Typical room-temperature mechanical requirements for LF2 Class 1 and Class 2 include:

Property Requirement
Tensile Strength 485–655 MPa
Yield Strength ≥250 MPa
Elongation, round specimen ≥22%

Final acceptance must follow the specified edition of ASTM A350 / ASME SA-350 and the purchase order.

LF2 Class 1 vs Class 2

The most important difference between LF2 Class 1 and Class 2 is the Charpy V-notch impact requirement.

Item LF2 Class 1 LF2 Class 2
Standard CVN Test Temperature −46°C / −50°F −18°C / 0°F
Average Energy, full-size specimen 20 J minimum 27 J minimum
Typical Selection Lower-temperature service Less severe low-temperature service

Therefore, an RFQ should not simply state “A350 LF2” when the project requires a specific class.

The required class should be stated explicitly.

Heat Treatment

LF2 forgings are heat treated to achieve the required mechanical properties and low-temperature toughness.

Permitted heat-treatment routes may include:

  • normalizing;
  • normalizing and tempering;
  • quenching and tempering.

The actual condition must comply with the applicable material specification and project requirements.

“LF2N” or “SA-350N” should not be used as a substitute for the formal material grade unless the purchase specification clearly defines the intended normalized condition.

ASME B16.5 and LWN Flanges

ASME B16.5 defines pressure-temperature ratings, dimensions, facing, bolting, tolerances and marking for standard pipe flanges.

For an LWN flange, standard flange-end features may follow ASME B16.5, including:

  • outside diameter;
  • bolt circle;
  • bolt-hole pattern;
  • flange thickness;
  • raised face or RTJ geometry;
  • pressure class.

However, the extended neck or barrel of an LWN flange is commonly project-specific.

Therefore:

ASME B16.5 does not by itself define every dimension of a custom Long Weld Neck Flange.

Neck length, bore, transition profile and weld-end dimensions should be specified by drawing or RFQ.

LWN Flange vs Standard Weld Neck Flange

Item LWN Flange Standard WN Flange
Neck Extended Standard tapered hub
Typical Use Vessel nozzle / equipment connection Piping connection
Neck Length Often custom Standardized
Bore Drawing / equipment dependent Pipe schedule dependent
Flange End May follow B16.5 B16.5
Manufacturing Forged Forged

An LWN flange should therefore not be assumed to be dimensionally identical to a standard ASME B16.5 welding neck flange.

Manufacturing & Inspection

A typical production route is:

Forging → Heat Treatment → UT → Rough Machining → Final Machining → MT → Dimensional Inspection

Inspection can include:

  • chemical analysis;
  • tensile testing;
  • Charpy V-notch impact testing;
  • hardness;
  • ultrasonic testing;
  • dimensional inspection;
  • flange facing inspection;
  • bore inspection;
  • PMI where specified;
  • third-party inspection.

Additional requirements must be stated in the RFQ or PO.

Applications

SA-350 LF2 LWN flanges are commonly used for:

  • pressure vessel nozzles;
  • shell-and-tube heat exchangers;
  • separators;
  • reactors;
  • LNG and LPG systems;
  • low-temperature oil & gas equipment;
  • petrochemical plants;
  • low-temperature piping systems.

How to Order an LF2 LWN Flange

A complete RFQ should include:

Size + Pressure Class + Facing + Material Grade/Class + Neck Length + Bore + Weld End + Design Standard + Drawing + Inspection Requirements

Example:

LONG WELD NECK FLANGE, NPS 8, CLASS 600, RF, ASME SA-350 LF2 CL.1, FLANGE END TO ASME B16.5, NECK LENGTH AND BORE AS PER DRAWING, CVN + UT + MT REQUIRED

FAQ

What is an A350 LF2 Long Weld Neck Flange?

It is a forged low-temperature carbon steel flange with an extended neck, commonly used as a vessel or heat-exchanger nozzle.

Is an LWN flange fully standardized by ASME B16.5?

Not necessarily. The flange face and bolting dimensions may follow B16.5, while the extended neck, bore and transition geometry are often custom.

What is the difference between LF2 Class 1 and Class 2?

The main difference is the specified Charpy impact test condition. Class 1 is tested at a lower temperature than Class 2.

Is LF2 the same as A105?

No. They are different material specifications. A350 LF2 specifically requires notch-toughness control for low-temperature service.

Can an LF2 LWN flange be made to a customer drawing?

Yes. Custom neck length, bore, wall thickness and transition geometry can be manufactured according to approved drawings and applicable design requirements.

ASTM A350 LF2 Long Weld Neck Flange

ASTM A350 LF2 Long Weld Neck Flange

SA-350 LF2 LWN Flange Manufacturer Supplier

We supply ASME SA-350 LF2 Long Weld Neck Flanges for pressure vessels, heat exchangers and low-temperature piping systems.

Custom LWN flanges can be forged and machined according to customer drawings with specified CVN impact testing, UT, MT, dimensional inspection and third-party inspection.

For quotation, provide the size, pressure class, facing, LF2 class, neck length, bore, drawing and inspection requirements.


0 Comments

Leave a Reply

Your email address will not be published. Required fields are marked *