ASTM A320 L43 Stud Bolts | Low-Temperature Bolting & Heavy Hex Nuts
ASTM A320 Grade L43 stud bolts are quenched-and-tempered alloy steel fasteners designed for low-temperature pressure equipment, flanges, valves, fittings and piping systems.
Grade L7 is commonly manufactured from the AISI 4140 / 4142 alloy steel family, while Grade L43 is based on AISI 4340 nickel-chromium-molybdenum alloy steel.
L43 provides greater hardenability and is particularly useful for larger-diameter low-temperature bolting where the required mechanical and Charpy impact properties must be maintained through a larger section.
Available products include fully threaded stud bolts, flange studs, double-end studs and matching ASTM A194 Grade 7 / 7M heavy hex nuts according to project requirements.
ASTM A320 L7 and L43 Overview
| Item | Grade L7 | Grade L43 |
|---|---|---|
| Standard | ASTM A320 / A320M | ASTM A320 / A320M |
| Alloy Family | Cr-Mo Steel | Ni-Cr-Mo Steel |
| Typical Base Material | AISI 4140 / 4142 | AISI 4340 |
| Heat Treatment | Quenched & Tempered | Quenched & Tempered |
| Typical Size Capability | Up to 2-1/2″ for specified strength level | Up to 4″ for specified strength level |
| Tensile Strength | 125 ksi / 860 MPa min | 125 ksi / 860 MPa min |
| Yield Strength | 105 ksi / 725 MPa min | 105 ksi / 725 MPa min |
| Low-Temperature Impact | Required | Required |
| Typical Nuts | ASTM A194 Grade 7 | ASTM A194 Grade 7 |
What Is ASTM A320?
ASTM A320 / A320M covers alloy and stainless steel bolting materials and bolting components for low-temperature service.
Typical products include:
- Stud Bolts
- Flange Studs
- Fully Threaded Studs
- Double-End Studs
- Bolts
- Nuts
- Custom Low-Temperature Fasteners
The specification requires control of chemical composition, heat treatment, tensile properties, hardness and Charpy impact performance.
ASTM A320 Grade L43 Stud Bolts
Grade L43 is based on AISI 4340 nickel-chromium-molybdenum alloy steel.
The nickel addition and higher hardenability of 4340 make L43 particularly suitable for large-diameter low-temperature bolting.
Grade L43 is capable of achieving the specified strength and impact properties in diameters up to approximately 4 in., whereas the comparable L7 mechanical-property range is generally limited to smaller diameters.
L43 should not be described as a grade used only above 2-1/2 in. It can also be supplied in smaller diameters when specified by the purchaser.
L7 vs L43
The primary difference between L7 and L43 is the alloy system and resulting hardenability.
| Property | L7 | L43 |
|---|---|---|
| Typical Steel | AISI 4140 / 4142 | AISI 4340 |
| Chromium | Yes | Yes |
| Molybdenum | Yes | Yes |
| Nickel | Generally No | 1.65–2.00% |
| Hardenability | High | Higher |
| Large Diameter Capability | More Limited | Better |
| Low-Temperature Service | Yes | Yes |
For large-diameter critical bolting, L43 may be selected where L7 cannot reliably achieve the required through-section mechanical and impact properties.
Chemical Composition
Typical chemistry is:
| Element | L7 | L43 |
|---|---|---|
| Carbon | 0.37–0.49% | 0.38–0.43% |
| Manganese | 0.65–1.10% | 0.60–0.85% |
| Phosphorus | 0.035% max | 0.035% max |
| Sulfur | 0.040% max | 0.040% max |
| Silicon | 0.15–0.35% | 0.15–0.35% |
| Chromium | 0.75–1.20% | 0.70–0.90% |
| Nickel | — | 1.65–2.00% |
| Molybdenum | 0.15–0.25% | 0.20–0.30% |
Actual chemical composition is reported on the Material Test Certificate.
For L43 required to meet severe low-temperature impact requirements, tighter control of phosphorus, sulfur and steel cleanliness may be necessary.
Mechanical and Impact Properties
Typical requirements for the applicable size range include:
| Property | L7 | L43 |
|---|---|---|
| Tensile Strength | 125 ksi / 860 MPa min | 125 ksi / 860 MPa min |
| Yield Strength | 105 ksi / 725 MPa min | 105 ksi / 725 MPa min |
| Elongation | 16% min | 16% min |
| Reduction of Area | 50% min | 50% min |
| Typical Charpy Test Temperature | -150°F / -101°C | -150°F / -101°C |
Impact-test temperature and acceptance values should follow the applicable ASTM A320 requirements and any additional project specification.
ASME B18.31.2 Stud Bolts
Inch-series L7 and L43 flange stud bolts can be manufactured to ASME B18.31.2.
Available configurations include:
- Fully Threaded Stud Bolt
- Flange Stud
- Continuous-Thread Stud
- Double-End Stud
- Tap-End Stud
Unified inch threads are normally specified according to ASME B1.1.
Common thread series include:
- UNC
- UNF
- 8UN
8UN is widely used for large-diameter flange bolting.
ASTM A194 Heavy Hex Nuts
ASTM A320 low-temperature stud bolts are normally supplied with compatible impact-tested nuts.
Common combinations include:
ASTM A320 L7 Stud Bolt + ASTM A194 Grade 7 Heavy Hex Nuts
and, where the project specifically requires controlled hardness:
ASTM A320 L7M Stud Bolt + ASTM A194 Grade 7M Heavy Hex Nuts
L43 stud bolts are commonly supplied with ASTM A194 Grade 7 heavy hex nuts or other project-specified compatible nut grades.
Nut material, impact requirements, hardness and thread fit should be clearly stated in the purchase order.
Coatings and Surface Treatments
Available finishes include:
- Plain / Black Finish
- Zinc Plating
- Zinc-Nickel Plating
- Hot-Dip Galvanizing
- Mechanical Galvanizing
- PTFE / Fluoropolymer Coating
- Xylan-Type Coating
- Zinc + Fluoropolymer
- Zinc-Nickel + Fluoropolymer
- Project-Specified Coating
Coating selection should consider corrosion exposure, operating temperature, required friction coefficient and tightening procedure.
Typical Applications
ASTM A320 L7 and L43 stud bolts are commonly used in:
- LNG Facilities
- Gas Processing Plants
- Low-Temperature Pressure Vessels
- Cryogenic Process Equipment
- Oil and Gas Facilities
- Petrochemical Plants
- Heat Exchangers
- Valves
- Pipeline Flanges
- Offshore Equipment
Actual material suitability depends on the specified design temperature and applicable design code.
Inspection and Certification
L7 and L43 stud bolts can be supplied with:
- EN 10204 Type 3.1 MTC
- Chemical Analysis
- Mechanical Testing
- Charpy Impact Testing
- Hardness Testing
- PMI
- Thread-Gauge Inspection
- Dimensional Inspection
- Coating Inspection
- Third-Party Inspection
- Full Heat-Number Traceability
How to Order ASTM A320 L43 Stud Bolts
Example 1
ASTM A320 L7 Stud Bolt, 1-1/2″-8UN × 12″, Fully Threaded, with 2 ASTM A194 Grade 7 Heavy Hex Nuts, EN 10204 3.1
Example 2
ASTM A320 L43 Stud Bolt, 3″-8UN × Custom Length, ASME B18.31.2, with 2 ASTM A194 Grade 7 Heavy Hex Nuts
Example 3
ASTM A320 L43 Stud Bolt, 3″-8UN × 980 mm Overall Length, Fully Threaded, with 2 Heavy Hex Nuts, Zinc Base Coat + Fluoropolymer Coating, Flat Washers
Frequently Asked Questions
What is the difference between ASTM A320 L7 and L43?
L7 is typically based on AISI 4140 / 4142 Cr-Mo alloy steel, while L43 is based on AISI 4340 Ni-Cr-Mo steel. L43 offers higher hardenability and is particularly suitable for larger-diameter low-temperature bolting.
Is L43 only used above 2-1/2 inches?
No. L43 can also be supplied in smaller diameters. Its main advantage is that the required mechanical and impact properties can be achieved in larger sections, with ASTM A320 covering L43 sizes up to approximately 4 in. for the specified strength level.
What nuts are used with A320 L7?
ASTM A194 Grade 7 heavy hex nuts are commonly used with L7. L7M is commonly paired with Grade 7M nuts when the applicable project requirements call for the lower-hardness material combination.
Can L43 stud bolts use 8UN threads?
Yes. Large-diameter L43 flange stud bolts can be supplied with 8UN threads according to ASME B1.1.
Related Low-Temperature Bolting Products
- ASTM A320 L7 Stud Bolts
- ASTM A320 L7M Stud Bolts
- ASTM A320 L43 Stud Bolts
- ASTM A194 Grade 7 Heavy Hex Nuts
- ASTM A194 Grade 7M Heavy Hex Nuts
- ASME B18.31.2 Stud Bolts
- PTFE / Fluoropolymer Coated Stud Bolts


ASTM A320 L7 & L43 Stud Bolt Supplier
We manufacture and supply ASTM A320 L7, L7M and L43 stud bolts and matching heavy hex nuts for low-temperature pressure equipment, flange and piping applications.
Available products include fully threaded studs, flange studs, double-end studs, 8UN large-diameter stud bolts and coated bolting assemblies.
For quotation, please provide the grade, diameter, length, thread, nut requirement, coating, quantity, impact requirement and certification.
ASTM Standards
A194/A194M Specification for Carbon Steel, Alloy Steel, and Stainless Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both
F436/F436M Specification for Hardened Steel Washers Inch and Metric Dimensions
F606/F606MTest Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
The mechanical and chemical makeup of both A320 Grades L7 and L43, is almost same,but the main difference is that the raw material used to make A320 L7 fasteners is typically 4140, whereas the raw material used to make A320 L43 is 4340.You may find the ASTM A320 specification showing below