Gost 9940-81 08X18H10T stainless steel tube 08KH18N10T – 1.4541 – aisi 321 tube

We are the professional exporter and supplier of Gost 9940-81 08X18H10T stainless steel tube in China.

Standard: Gost 9940-81 , ASTM A312, EN10216-5
Grade: 08X18H10T 12X18H10T, 12Cr18Ni10Ti
SIZE: 6-630MM
WT: 1-40MM

08X18H10T material is Russia GOCT standard stainless steel and heat resistant steel steel grade and chemical composition.

Chemical composition of 08X18H10T, 08X18H10T mechanical properties, 08X18H10T datasheet, 08X18H10T equivalent grade, Heat treatment and temperature process of 08X18H10T.

GOST 9940-81 Seamless hot-formed pipes from corrosion-resistant steel.

Pipe manufactured in accordance with the requirements of this standard and technical regulations approved in the prescribed manner, of the steel grades listed in table.3, with the chemical composition according to GOST 5632, micro rare earth metals.

GOST 9940-81 08X18H10T Stainless Steel Tube 08KH18N10T - 1.4541 - aisi 321 Pipes

The sulfur content in steel, intended for the manufacture of pipes to be welded that is specified in the order, shall not exceed 0.020%.
Pipes are produced heat-treated or without heat treatment in accordance with the order.

08KH18N10T is made according to the following GOST: 5632−72; 18 907−73, 4405−75, 5582−75, 5949−75; 25 054−81; 9940−81.This steel is a chromium-Nickel austenitic alloy. Is smelted in electric-arc furnaces. Has high resistance to intergranular corrosion in industrial environments, in comparison with the alloys and the 12KH18N10T 12X18H12T. It is used in the manufacture of welded structures operating in highly-corrosive environments at t° from -196 to +600°C without pressure limitation.

08X18H10T Composition (GOST 5632−72)

C	Cr	Fe	Mn	Ni	P	S	Si	Ti
≤0,08	17−19	DOS.	≤2	9−11	≤0,035	≤0,02	≤0,8	5·S-0,7

Corrosion resistance

According to GOST 5582−72, 7350−77 and 4986−79 such steel when tested by the methods AM and AMU GOST 6032−89 resists intergranular corrosion in the test solutions during exposure, respectively, 8 and 24 hours. These tests are conducted after annealing (1 hour) at t° 650 °C.

Technological parameters

Steel 08KH18N10T on the technological parameters of a similar brand 12X18H9T (10T). From them it has a better resistance weld to intergranular corrosion and knife in the chemical industry.

Mechanical properties of rolled in t^o 20^o With

Assortment	GOST	σ_In	σ_T	δ₅	Heat treatment
Sheet 1 — 4 mm	5582−75	530	205	40	Hardening 1050 — 1080^o C, Cooling water,
The plates	7350−77	510	205	43	Hardening 1030 — 1080^o C, Cooling air,
Forgings	25 054−81	490	196	35−38
Rod Ø 60	5949−75	490	196	40	Hardening 1020 — 1100^o C, Cooling air,
Rod full hard	18 907−73	880−930
Pipe	10 498−82	529	40
Pipe	11 068−81	530	216	37
Pipe cold deformitatii	9941−81	549	37
Tubes hot deformation	9940−81	510	40

σ_In the limit of short-term strength;

σ_T is the yield stress for permanent deformation;

∆ ₅ — elongation at break.

Welding

In automatic welding under the flux using the same filler materials as for the alloy 12X18H9T (10T)

How to order our 08X18H10T Tubes?

Example

Pipe 426×18 – 08X18H10T according to the type of GOST 9940-81 Seamless hot-worked pipe made of corrosion-resistant steel – 109meters

Pipe 377×18 – 08X18H10T according to the type of GOST 9940-81 Seamless hot-worked pipe made of corrosion-resistant steel – 8meters

gost 9940-81 08X18H10T stainless steel tube 08KH18N10T – 1.4541 – aisi 321 tube

Published by ADMIN on

Gost 9940-81 08X18H10T stainless steel tube 08KH18N10T – 1.4541 – aisi 321 tube

We are the professional exporter and supplier of Gost 9940-81 08X18H10T stainless steel tube in China.

08X18H10T material is Russia GOCT standard stainless steel and heat resistant steel steel grade and chemical composition.