ASTM A333 GR.6 Seamless Pipe, ASTM A333 Grade 6 Low Temperature Seamless Pipes,A333 Gr.6 Pipe
We are a professional astm-a333-grade-6-pipe,A333 Grade 6 Seamless steel pipe ,ASTM A333 Steel Pipes, ASME SA333 Gr.6 Low Temperature Pipes, A333 Gr.6 Seamless Pipe supplier and exporter in China.
ASTM A333 Grade 6 pipe is common use material for low temperature services in above -45℃
China ASTM A333 Grade 6 pipe specifications
Sizes: 1/2″ to 24”
WT Schedules: SCH 10, SCH 40, SCH 80 to SCH 160
Length: Single Random Length, Double Random Length, 20 ft, 40 ft
Ends Types: Plain, Beveled
Material Grade:ASTM A333 Grade 6
ASTM A333 SEAMLESS LOW TEMPERATURE CARBON STEEL PIPE (LTCS PIPE)
ASTM A333 Seamless and Welded Steel Pipe for Low-Temperature Service
Standard Specification for Seamless and Welded Steel Pipe for Low-Temperature Service and Other Applications with Required Notch Toughness
ASTM A333 Gr 6 pipes Inspection and Test: Chemical Composition Inspection, Mechanical Properties Test(Tensile Strength,Yield Strength, Elongation, Flaring, Flattening, Bending, Hardness, Impact Test), Surface and Dimension Test,No-destructive Test, Hydrostatic Test.
Surface treatment: Oil-dip, Varnish, Passivation, Phosphating, Shot Blasting.
Both ends of each crate will indicate the order no., heat no., dimensions, weight and bundles or as requested.
ASTM A333 Grade 6 seamless pipe Chemical Compositions(%)
Mechanical properties for ASTM A333 Grade 6 Seamless pipe
| Properties | Data |
| Tensile strength, min, (MPa) | 415 Mpa |
| Yield strength, min, (MPa) | 240 Mpa |
| Elongation, min, (%), L/T | 30/16.5 |
ASTM A333 Gr 6 pipes Impact requirements:
the notched-bar impact properties of each set of three impact specimens, when tested at temperature specified shall be not less than the values prescribed.
A333 Grade 6 :
35 ksi (240 MPa) min. YS
60 ksi (415 MPa) min. UTS
Impact Tested to meet
Minimum 18J (13 ft-lb) at
-46°C (-50°F)
A333 Grade 6 seamless Pipe Heat Treatment condition:
A333 Grade 6 Pipe should be Normalized at 1500 F and air cooled.
Quenched and tempered by heating to 1475 F.
Temper by re-heating to 1100 F and rapid air cooling.
When the pipes, fittings, valves, bolts and nuts are connected in the pipeline, usually the material grades should be the same grade.
The Astm A333 Gr 6 Pipes is used to produce A420 WPL6 Pipe fittings,and match with ASTM A350 LF2 Flanges, and A320 Gr L7 stud bolts & A194 Gr 7 hex nuts in the pipeline connections.
| Material | Pipes | Buttweld Fittings | Forged Steel Fittings | Valves | Bolts and Nuts |
| Low Temp Carbon Steel | A333 GR6 | A420 WPL6 | ASTM A350 LF2 | A352 LCB | A320 Gr L7 /A194 Gr 7 |
ASTM A333 GR.6 Pipes Charpy V-Notch Impact Test
Toughness, or ductility, is the ability of a material to resist impact, to withstand repeated reversals of stress, or to absorb energy when stressed beyond the elastic limit. Steel is normally considered to be a ductile material, however, it may shatter just as glass at certain low temperatures. The critical ductile-to-brittle transition temperature (CDBTT) for any steel is the temperature above which the steel behaves in a predominantly ductile manner and below which it behaves in a predominantly brittle manner. The low alloy steel pipe of ASTM A333 Gr.6 with a low CDBTT can be used at temperatures down to -45°C [-50°F]. It is important to verify that the pipe materials are impact tested and exhibit a sufficient high Charpy toughness.
The Charpy V-notch impact test shall be conducted at -45°C [-50°F] with three testing specimens in the size of 10 mm x 10 mm x 55 mm. The minimum average energy absorbed for three specimens shall be 18 J [13 ft*lbf], and the minimum energy absorbed for each specimen is 14 J [10 ft*lbf]. The actual tests have been done to three specimens which were taken from ASTM A333 Gr.6 seamless pipes produced by BAOSTEEL. The results listed in the table below indicate that the steel exhibits superior impact toughness, which is at least 20 times higher than the standard value.
However,we can supply the ASTM A333 GR.6 Pipes with impact testing at minus 52° С (-52° С). Impact test result
(Charpy test on V-notch specimen) shall be at least 27 J/cm2
ASTM A333 GR.6 Pipe NDE Testing
All pipes shall be subject to a hydrostatic testing. The actual test pressure value shall be shown in the inspection certificate. In case applicable ASTM specification has no details regarding hydrostatic testing ASTM A999-2018 shall be applied.
Referenced Documents
- ASTM A 370 Test Methods and Definitions for Mechanical testing of Steel Products
- ASTM A999/A 999M Specification for General requirements for Alloy and Stainless Steel Pipe.
- ASTM A 671 Specification for General requirements for Alloy and Stainless Steel Pipe
- ASTM E 23 Test Methods for Notched bar Impact testing of Metallic Materials
How to order our Astm A333 Gr 6 Seamless Pipes?
PIPE , A333 GR.6, 80, NPS10 Pipe, Carbon Steel Per ASTM A333 Grade 6, Schedule 80, Seamless, Bevelled Both Ends, Per ANSI B36.10, To be Supplied in Double Random Lengths
PIPE MET, A333 GR.6, 20, NPS24 Pipe, Carbon Steel Per ASTM A333 Grade 6, Schedule 20, Seamless, Bevelled Both Ends, Per ANSI B36.10, To be Supplied in Double Random Lengths
ASTM A333 Gr.6 Seamless Steel Pipe 8 Inch x SCH 40,6 metres length
ASTM A333 Gr.6 Seamless Pipe, SCH 40, 4IN, 6 Meters
We carry stock for ASTM A333 Gr.6 Seamless pipes
Труба бесш. / PIPE SMLS 1″ SCH XS BB ASTM A333 GR.6 ASME B36.10/19 SMLS 33.4 4.55 A333 GR6
Труба бесш. / PIPE SMLS 1.5″ SCH XS BB ASTM A333 GR.6 ASME B36.10/19 SMLS 48.26 5.08 A333 GR6
Труба бесш. / PIPE SMLS 2″ SCH STD BB ASTM A333 GR.6 ASME B36.10/19 SMLS 60.33 3.91 A333 GR6
Труба бесш. / PIPE SMLS 4″ SCH STD BB ASTM A333 GR.6 ASME B36.10/19 SMLS 114.3 6.02 A333 GR6
Труба бесш. / PIPE SMLS 6″ SCH STD BB ASTM A333 GR.6 ASME B36.10/19 SMLS 168.28 7.11 A333 GR6
Труба бесш. / PIPE SMLS 8″ SCH 30 BB ASTM A333 GR.6 ASME B36.10/19 SMLS 219.1 7.04 A333 GR6
Труба бесш. / PIPE SMLS 10″ SCH 30 BB ASTM A333 GR.6 ASME B36.10/19 SMLS 273.05 7.8 A333 GR6
Труба бесш. / PIPE SMLS 16″ SCH XS BB ASTM A333 GR.6 ASME B36.10/19 SMLS 406.4 12.7 A333 GR6
